We Offer Revolution Of Industrial Engineering
More Information
+1 (561) 757-5620
+1 (561) 757-5620
DESCRIPTION AND RECOMMENDED USES: 100% solids, Dura-Coat Industrial floor 600 is a solvent free, Epoxy coating ambient-temperature curing. It is designed particularly as protective coating for concrete floors (or equivalent). Dura-Coat Industrial Floor 600 is convenient-to-use, self-leveling with excellent traffic resistance and high mechanical strength.
| Maximum Temperature (Dependent on service) | Wet Service | Dry Service | 50°C | 60°C | 122°F | 140°F |
|---|---|---|---|
| Chemical Resistance | Water | Alkalis | Inorganic Acids | Organic Acids | Organic Solvents | Excellent | Excellent | Good | Good | Good | |
| Solids by Volume | 100% | ||
| Mixed Density | 1.25 | ||
| Shore D Durometer Hardness | (ASTM D 2240) | 82 | |
| Pot life | 25 MIN / KG at 72ºF | ||
| Vertical SAG Resistance at 21°C (70°F) and 0.635mm (25mils) | No sag | ||
| Coverage for 10L kit | 108sf@40mils | 10m²@1mm | |
| Mix Ratio | 2:1 by weight | Base: Activator | |
| Color | Grey, green, red, orange, blue and yellow | ||
| Shelf life (unopened containers) | 3 years at 55-95ºF (13-35ºC) | ||
Surface Preparation
Proper surface preparation is critically important for the long-term performance of the Dura-Coat Industrial Floor 600. The prepared concrete surface must be structurally sound, free from all contaminants and roughened to an >ICRI CSP 3 profile (similar to #60 grit sandpaper). If using with Dura-Coat Krete-Seal 800, surface may be damp, but not wet i.e. no free-standing water. Dura-Coat Industrial Floor 600 can be applied on damp concrete without using Dura-Coat Krete-Seal 800. A vapor barrier (Krete-Seal 800) is required for slab on grade application. If no vapor barrier is present, check for vapor transmission.
Surface Cleaning & Profiling Methods
Hydro-Blasting Scarifying
Steel Shot-Blasting Dry Abrasive Blasting
Mixing
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by Weight 2-part Base to 1-part Activator. Mix thoroughly to produce an even colored and streak-free material. THINNING: Never thin.
Application
Application temperature range 10°C (50°F)-32°C (90°F) (substrate).
Dura-Coat Industrial Floor 600 may be applied by notched squeegee, spray system, brush, or roller.
Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating (epoxy glued bristles are best). Trim or tape to <1” nap.
Roller: use good quality 1/8” nap.
For maximum protection against immersion or spills, a 2-coat system is recommended.
To avoid sagging on vertical surfaces the maximum wet film thickness should be between 500 μm-1000 μm (20-40 mil) per coat.
| 16°C (60°F) | 25°C (77°F) | 32°C (90°F) | |
|---|---|---|---|
| Tack Free | 6 hours | 3 hours | 2 hours |
| Light Load | 18 hours | 10 hours | 6 hours |
| Overcoat End | 24 hours | 16 hours | 8 hours |
| Full Load | 36 hours | 24 hours | 12 hours |
| Full Chemical | 72 hours | 36 hours | 18 hours |
Clean Up
Tools must be immediately cleaned after usage by using industrial alkaline detergent.
Safety
Before using any products, review the appropriate Safety Data Sheet (SDS) or Safety Sheet for your area. Follow standard confined space entry and work procedures, if appropriate.