Dura-Coat Surface Tolerant 610
Technical Data Sheet
DESCRIPTION AND RECOMMENDED USES: 100% solids, Dura-Coat 610 is a solvent free, ceramic filled coating designed particularly as a protective coating for metallic surface where only a mechanical preparation is available and for dump sufarces as well. Excellent in a wide array of caustics and acids. Dura-Coat 610 can be easily applied by brush or roller up to 25 mils without slump.
- It can be applied up to 25 mils without slump
- Suitable for any substrate, steel, bronze, aluminum, concrete
- Suitable for corrosion and abrasion protection
Application Areas:
- Bins and Silos
- Screw conveyors
- Water boxes
- Heat exchangers
- Fans and housings
- Valves
- Pump cases
- Tanks linings
- Metallic structures
- Coal crushers
- Many others
Packages
- Size 1Kg | Reorder # 610-01
- Size 2Kg | Reorder # 610-02
- Size 7.5Kg | Reorder # 610-7.5
- Size 15Kg | Reorder # 610-15
Technical Data
| Maximum Temperature (Dependent on service) | Wet Service | Dry Service | 90°C | 150°C | 194°F | 320°F |
|---|---|---|---|
| Chemical Resistance | Water | Alkalis | Inorganic Acids | Organic Acids | Organic Solvents | Excellent | Excellent | Good | Good | Good | |
| Solids by Volume | 100% | ||
| Mixed Density | 1.4 | ||
| Shore D Durometer Hardness | (ASTM D 2240) | 80 | |
| Pot life | 25 MIN / KG at 72ºF | ||
| Vertical SAG Resistance at 21°C (70°F) and 0.635mm (25mils) | No sag | ||
| Coverage for 10Kg kit | 115sf @20mils | 10.7m²@500micron | |
| Mix Ratio | 2:1 by weight | Base: Activator | |
| Color | Gray as standard. Blue and Red optional. Other colors contact the manufacture | ||
| Shelf life (unopened containers) | 3 years at 55-95ºF (13-35ºC) | ||
Application Sheet
Surface Preparation: Proper surface preparation is critical to the long-term performance of this product. The exact requirements for surface preparation vary with the severity of the application, expected service life, and the initial substrate conditions. All sharp edges and welds shall be ground smooth or to a 3 mm (120 mil) radius before abrasive blasting or mechanical preparation. The preparation must be mechanical minimum St2 or St3.
Mixing: Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by weight 2-parts Base to 1-part Activator. Mix thoroughly to produce an even colored and streak-free material. THINNING: Never thin.
Application: Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating (epoxy glued bristles are best). Trim or tape to <1” nap.
Roller: use good quality 1/8” nap.
Curing Schedule
| 16°C (60°F) | 25°C (77°F) | 32°C (90°F) | |
|---|---|---|---|
| Tack Free | 6 hours | 4 hours | 3 hours |
| Light Load | 12 hours | 8 hours | 6 hours |
| Overcoat End | 16 hours | 10 hours | 8 hours |
| Full Load | 24 hours | 16 hours | 12 hours |
| Full Chemical | 48 hours | 24 hours | 18 hours |
Clean Up
Tools must be immediately cleaned after usage by using industrial alkaline detergent.
Safety
Before using any products, review the appropriate Safety Data Sheet (SDS) or Safety Sheet for your area. Follow standard confined space entry and work procedures, if appropriate.
Manufacturer, Dura-Coat Industrial Inc., makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential, or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Dura-Coat Industrial Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer. DURA-COAT® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets, and any other information as supplied in writing directly from manufacturers technical support.
Revision: 11/17/2020