Dura-Coat Industrial Floor 600
Technical Data Sheet
DESCRIPTION AND RECOMMENDED USES: 100% solids, Dura-Coat Industrial floor 600 is a solvent free, Epoxy coating ambient-temperature curing. It is designed particularly as protection coating for concrete floor, Dura-Coat Industrial Floor 600 is convenient-to-use, self-leveling with excellent traffic resistance and high mechanical strength.
- Easy to apply and quick back in service
- Ideally suited for concrete protection
- Suitable for abrasion protection
- Suitable for high traffic
Application Areas
- Industrial areas
- High traffic areas
- Maintenance shop
- Aisle-ways
- Warehouse
- Manufacturing areas
Packages
Grey
- Size 5L | Reorder # 600-GY5L
- Size 10L | Reorder # 600-GY10L
Green
- Size 5L | Reorder # 600-GR5L
- Size 10L | Reorder # 600-GR10L
Red
- Size 5L | Reorder # 600-R5L
- Size 10L | Reorder # 600-R10L
Orange
- Size 5L | Reorder # 600-O5L
- Size 10L | Reorder # 600-O10L
Blue
- Size 5L | Reorder # 600-B5L
- Size 10L | Reorder # 600-B10L
Yellow
- Size 5L | Reorder # 600-Y5L
- Size 10L | Reorder # 600-Y10L
Technical Data
| Maximum Temperature (Dependent on service) | Wet Service | Dry Service | 50°C | 60°C | 122°F | 140°F |
|---|---|---|---|
| Chemical Resistance | Water | Alkalis | Inorganic Acids | Organic Acids | Organic Solvents | Excellent | Excellent | Good | Good | Good | |
| Solids by Volume | 100% | ||
| Mixed Density | 1.25 | ||
| Shore D Durometer Hardness | (ASTM D 2240) | 82 | |
| Pot life | 25 MIN/KG at 72ºF | ||
| Coverage for 10 L kit | 108sf@40mils | 10m²@1mm | |
| Mix Ratio | 2:1 by weight | Base: Activator | |
| Color | Grey, green, red, orange, blue and yellow | ||
| Shelf life (unopened containers) | 3 years at 55-95ºF (13-35ºC) | ||
Application Sheet
Surface Preparation
Proper surface preparation is critically important for the long-term performance of the Dura-Coat Industrial Floor 600. The prepared concrete surface must be structurally sound, free from all contaminants and roughened to an >ICRI CSP 3 profile (similar to #60 grit sandpaper). If using with Dura-Coat Krete-Seal 800, surface may be damp, but not wet i.e. no free-standing water. Dura-Coat Industrial Floor 600 can be applied on damp concrete without using Dura-Coat Krete-Seal 800. A vapor barrier (Krete-Seal 800) is required for slab on grade application. If no vapor barrier is present, check for vapor transmission.
Surface Cleaning & Profiling Methods
Hydro-Blasting Scarifying
Steel Shot-Blasting Dry Abrasive Blasting
Mixing
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by Weight 2-part Base to 1-part Activator. Mix thoroughly to produce an even colored and streak-free material. THINNING: Never thin.
Application
Application temperature range 10°C (50°F)-32°C (90°F) (substrate).
Dura-Coat Industrial Floor 600 may be applied by notched squeegee, spray system, brush, or roller.
Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating (epoxy glued bristles are best). Trim or tape to <1” nap.
Roller: use good quality 1/8” nap.
For maximum protection against immersion or spills, a 2-coat system is recommended.
To avoid sagging on vertical surfaces the maximum wet film thickness should be between 500 μm-1000 μm (20-40 mil) per coat.
Curing Schedule
| 16°C (60°F) | 25°C (77°F) | 32°C (90°F) | |
|---|---|---|---|
| Tack Free | 6 hours | 3 hours | 2 hours |
| Light Load | 18 hours | 10 hours | 6 hours |
| Overcoat End | 24 hours | 16 hours | 8 hours |
| Full Load | 36 hours | 24 hours | 12 hours |
| Full Chemical | 72 hours | 36 hours | 18 hours |
Clean Up
Tools must be immediately cleaned after usage by using industrial alkaline detergent.
Safety
Before using any products, review the appropriate Safety Data Sheet (SDS) or Safety Sheet for your area. Follow standard confined space entry and work procedures, if appropriate.
Manufacturer, Dura-Coat Industrial Inc., makes no warranty either expressed or implied including warranties of merchantability or fitness for a particular purpose for this product. Under no circumstances will the manufacturer be liable for incidental, consequential, or other damages, breach of warranty, strict liability, or any other theory arising out of use of this product. The information and or recommendations contained herein are based on standard Product and are proprietary and furnished solely for the use of our customers. This information is provided in good faith and believed to be true and accurate as of the date/version of this document. As the manufacturer has no control over the use conditions or application process of the parties using this product, the manufacturer cannot accept responsibility for loss, injury or other damages resulting from the use of the Product or this or any other information provided by the manufacturer. Therefore, no guarantees of any kind, expressed or implied, are made by the manufacturer, Dura-Coat Industrial Inc., regarding this, or any, product manufactured by them or any contracted or licensed manufacturer. DURA-COAT® epoxy products do not provide structural integrity or improvement. They are only used to provide protection from corrosion, wear, abrasion and chemical attack on a given substrate and only to the extent provided for in the Data Sheets, Technical Data Sheets, Safety Data Sheets, and any other information as supplied in writing directly from manufacturers technical support.
Revision: 4/2024